- 149
- 7 304 970
Ron Williams
Приєднався 24 жов 2011
Mobile Fix Automotive
Відео
Review of Rhinolights rock lights
Переглядів 7014 днів тому
Dimond duo rock lights. rhinoledlights.com/whip-lights/
Harbor Freight 30x16 cart assembly
Переглядів 23914 днів тому
how to quickly assemble the Franklin 30x16 plastic cart from harbor freight 58322
swapping from a Mendeola 2D to an S4
Переглядів 12714 днів тому
setting up the dash electronics to show proper gear on display.
reviewing a new fork brace on the 04 Goldwing. Kuryakyn 7339
Переглядів 98Місяць тому
reviewing a new fork brace on the 04 Goldwing. Kuryakyn 7339
LS engine coolant bleeding sandrail
Переглядів 641Місяць тому
All sand cars with an LS engine should have this bleed hose.
What makes a Deco case Mendeola stronger.
Переглядів 170Місяць тому
What makes a Deco case Mendeola stronger.
is your Mendeola a 2D or a Ebox
Переглядів 2482 місяці тому
how to properly tell what Mendeola you have.
Mendeola Ebox to 2D conversion part 4.
Переглядів 3852 місяці тому
Mendeola Ebox to 2D conversion part 4.
Mendeola Ebox to 2D conversion part 2
Переглядів 4683 місяці тому
Mendeola Ebox to 2D conversion part 2
Mendeola Ebox to 2D conversion step 1
Переглядів 2053 місяці тому
Mendeola Ebox to 2D conversion step 1
Mendeola 2D Flange drive seal replacement
Переглядів 3664 місяці тому
Mendeola 2D Flange drive seal replacement
SHORT VIDEO OF SATURDAY MORING LINEUP FATHER DAUGHTER GLAMIS TRIP
Переглядів 3504 місяці тому
SHORT VIDEO OF SATURDAY MORING LINEUP FATHER DAUGHTER GLAMIS TRIP
Difference between a Mendeola 2D and a Mendeola Ebox (short version)
Переглядів 5594 місяці тому
Difference between a Mendeola 2D and a Mendeola Ebox (short version)
product review of Rhino USA tie downs.
Переглядів 1435 місяців тому
product review of Rhino USA tie downs.
Mendeola 2D caught it just in time.
Переглядів 1,4 тис.5 місяців тому
Mendeola 2D caught it just in time.
Ok so what year RVs with 6.8 stop having ejections?
So what Calvin kit do I use for my 98 ford expadition eddie bouer 5.4 ? Said I had to make sure it's the rite one?
Hi Ron, Thanks for this awesome video. I live in San Jose, CA. Do you know of any shops near me that would do this repair on a 1997 e-350 v-10 van?
Mine has a slow leak. I have yet to do my 1st oil change........ I'll let you know.🤔
much appreciated ! intake is off and im making sure i dont make a mistake not going far enough with 'while we're at it' additional replacements etc. hmmm i might want to just get a new manifold for insurance i dont need to do this ALL OVER AGAIN should the plastic manifold fail or has an invisible defect
Cream soda blue
I know this video is 4yrs old but THANK YOU!! I was running in circles trying to figure out what the issue was with my 03 f150. Same exact symptoms after replacing coils and spark plugs. Makes sense with your diagnostic now!!!
Good stuff , answered all my questions.
Fabulous video. Logical, concise, helpful. My mechanic especially appreciates as it took him off the hook with my friends (doubters) who wanted me to blame him for the problem, that I said was just a coincidence and not his fault.
All the vehicles that blow out plugs should have been recalled and fixed with good heads or the customers should have got their money back.
The same thing happened to my 5.3. Turns out the number 6 intake lifter “separated “ from the barrel. Do you feel the need to replace both sides of engine? Odd side and even side. Or just replacement of one side is enough. Thanks
Was it slow start after engine warms up or cold starting. I have an 89 sbc slow start only after it warms up. I've tried everything but a new starter. It is a total rebuild
Install a Chevy Hot Start kit on starter
@SandCarServices if you're talking about a Ford solenoid, I already did.
@SandCarServices I have a 66 Ranchero with a 302 it starts fine hot. That's where I got the idea of adding a Ford solenoid under the hood.
@@Ronjovi77 so the "S" terminal on the starter solenoid is getting power directly from the positive post on battery? And the trigger wire from ignition is just turning on relay?
@SandCarServices I also have a 54 Chevy with 350 and a tbucket with a 66 hemi both with Ford solenoids that start fine at any temperature.
Same engine. Just p0171. Any suggestions? No vacuum leaks. Used a smoke machine. LS swap.
Thank you for an excellent video, it was a great help to me!
Very good Job 👍 .
Anyone know what under hood light hes using? Looking for a nice plug in like that. Thanks!
2015 Yukon here, started to get bumpy idle and rough low RPM driving. Noticed my oil pressure was only 20lb at idle. I suspicioned the AFM lifter fail issue because I've hated that system since I learned that it existed in my engine. Stupid insane idea to build something as destructive into an engine. I immediately got a Range Technology AFM disabler as soon as I bought the vehicle with 140K on it. It now has 220K and the rough idle just started at 220K. As a diagnostic I put 10/30 oil with Lucas additive in it rather than the GM recommended 5/20 "watery oil" viscosity. Brought the pressure up to 40lb like it should, apparently making the lifters work better, and the idle is almost normal now. It's been suggested to me by a mechanic it could be the lifters or might be an O-ring on the oil pickup tube lowering the pressure and making the (already somewhat damaged) lifters work badly.
Thank you sir! Very helpful. No need to edit! lol-
mine is leaking from the gaskets, where it had the rubber lines replaced. now, I have to replace both gaskets. It leaks after being driven.
I sub just bc of that bike
I love mine man but hers is so beautiful
Thank you Ron I believe I have the same problem. So its not really worth getting it smogged correct?
I have the po316&306&304. Fixed the spark plugs. The water tank is needed water a lot. Probably wont smog with engine light on. So its done. Am I right?
I have an 06 and mine has oil saturation on the outside of the hose and I have those exact codes, could that brake booster hose be my problem if it has oil on the outside of the hose?
I got a 08 6.2 with this code it shut off on my mechanic has put all types of parts on it chuld this be my issue
Omg. Never buy this car. They are completely junk
Before you all go taking apart the dash or glove box make sure you go under the hood and check the vacuum lines!
THe suspense at the end wow. No hole!
I blew one at 108k....had the mans tap a new thread set with a kit like this one. I think itbwas either cross threaded by me or put back in the way i took it out, euther way what i think factors in a lot is human repair errors. If another one goes i told my mechanic we will go ahead and do the other 7!
Great! This was very helpful 🫂
Hmmm, pay a $1000 or lock them open on an almost 10 year old car. What to do, what to do? I don’t need to flip a coin on this one
Question.. Can a bad fuel injector shut off that whole bank? Really hard to start due driver side bank not working, if i manage to get it stated after like 20 mns that side bank starts to work fine and i can drive it
Thank you I think this what going on with my 2016 ford fusion. With 50k miles on it. Great for life in Montana but in Az wtf lol. No one at autozone or ford knows about this it seems like. You get my like subscribe and comment for this ty.
I have installed this product on my 2001 7.3 and I bent the wires so they would stay away from gasket simply pushing wire is not enough because wire tension can push it back where you don't want it. Did my gaskets about 5 years ago 2019.
Thank you! As others have said, this is the only video I've seen on removing lower ball joints with rivets.
Ron - Many thanks for your tutorial on new belt routing sequence. Out of all videos posted of this procedure, your is the most efficient!
Good video. Much appreciated sir.
Best video I have ever seen.Sir you are a real mechanic and A even Better Teacher.Thanks for breaking down Afm to the Max!
I have short term zero and long term %25. That means I have vacuum leak too or maybe something else because I have P0068& P0106 on my mercedes benz C250
Thanks Ron for all your Tips!!!
Ron, What do you charge to install a calvan per cylinder?
I'm retired
If the engine has over 200k miles on it is it more likely it will not develop this issue?
I can confidently say. "Not true"
@@SandCarServices 👍👏😃
I wish I lived near you, I'd have you do my truck in a heartbeat. Since I'm in Va I'll have to do it myself. Thank you for the wonderful video. 😊
When you find the air leak and fix it how do you get rid of the permanent code?
Step one throw doorman intank in the trash step two spend the extra money on a ford unit
Has anyone encountered this issue happening while the tranny is downshifting awkwardly going up hill. It was 96 degrees and sunny going up a 7% grade. Only time it has happened so far.
Thank you! I’ve been trying to fix my 05 Mercury Mountaineer with this same issue for the last 4 months! The Arizona summer has been brutal! This was incredibly helpful and exactly what had happened to my max ac panel.
Mine failed in a month, wire covering split.. very handy.. Dorman is pure garbage. Thanks for the Video Ron!
Please help I need the kit
Your years are off on the IDI motor
Thanks for making this video, love the info! One question i do have is there a certain HP/TQ level where you recommend upgrading to the Deco Case?
It's more of a driving style than anything. I have broken way more parts with my Northstar than my LS 3
@@SandCarServices i plan to drive hard but with a honda v6 and 35 tensor baja bug, so deciding between deco and standard if its worth the $1500